Search results

Page title matches

• Joe test page 5
  This is a test page setup by joe to see if something works
  58 bytes (13 words) - 16:31, 23 November 2020

Page text matches

• 105.07 Handling and Transporting Materials
  ...sary. One exception is for borderline results in which case a copy of the test report should be included with the Transfer of Tested Materials form for th
  1 KB (183 words) - 14:49, 19 June 2017
• Joe test page 5
  This is a test page setup by joe to see if something works
  58 bytes (13 words) - 16:31, 23 November 2020
• Manual Section and Page Number
  ...to emphasize that the original not the re-typed or re-copied version of a test report must be submitted to the office daily. ** Included in the table for minimum frequency of testing the requirement to test the footprint of the sleeper slab foundation.
  1 KB (180 words) - 09:39, 3 January 2018
• Structural Fabrication Quality Manual
  ...shown in Chapter 2 by providing more detailed step by step inspection and test requirements, activity type, and potential option for reduced inspection (L
  3 KB (398 words) - 13:08, 4 August 2020
• Module:Documentation/config
  -- sandbox, and the location of test cases pages, etc. The module decides whether the page is a cfg['sandbox-notice-pagetype-template'] = '[[Wikipedia:Template test cases|template sandbox]] page'
  18 KB (2,100 words) - 09:28, 3 July 2014
• Mandrel Testing of Plastic Pipe
  ...dvantage. If the mandrel can be pulled through the entire run of pipe the test passes and the pipe can be accepted for deformation testing. ...ratory pipe rerounder is not an acceptable means to rectify failed mandrel test results.
  5 KB (826 words) - 16:06, 6 May 2021
• Hot Mix Asphalt Production Manual
  ...lishment of Ignition Oven Correction Factors; Calibration of Balance; Lift Test; Temperature Verification inside the Ignition Furnace (In-House Procedure); * Table: Minimum Test Methods Required for QA/QC Laboratory Qualification.
  4 KB (560 words) - 15:14, 19 June 2017
• 819 - Electrical and Lighting
  ...on requirements have not changed, this change simply allows other NRTLs to test and certify the conduit to Underwriters Laboratories Inc. (UL) standards.
  2 KB (225 words) - 08:33, 20 March 2015
• Division 3 Supplemental Information
  ...still be printed on the certificates. If the technician does not need to test concrete aggregates, successful completion of the Aggregate Testing Level O
  2 KB (220 words) - 13:20, 15 February 2017
• 105.01 Quality and Scope of Supply
  <center>Michigan Test Methods</center> ...y MDOT in testing certain materials, equipment or operations. Supplements test methods published by ASTM or AASHTO.
  5 KB (709 words) - 09:07, 15 April 2020
• 701 - Portland Cement Concrete for Structures
  ...l should be checked for markings, such as lot number, to identify with the test report. ...sting of the same concrete representing the first production lot to verify test results for temperature and air content of the concrete.
  15 KB (2,342 words) - 17:11, 6 May 2021
• 605 - Contractor Quality Assurance for Concrete
  ...te|Section 604]]. The QC staff is responsible for handling and curing the test specimens, and transporting them to the assigned MDOT Region testing labora ...y item compensates the Contractor for fabricating, handling and curing the test specimens, and transporting them to the assigned MDOT Region testing labora
  27 KB (4,041 words) - 16:33, 16 August 2016
• 710 - Waterproofing and Protective Covers
  ...ness and steel reinforcing pattern, but be at least 3 inches thick. After test panel placement, the concrete must be kept continuously wet and above 40 de
  9 KB (1,343 words) - 14:52, 17 January 2019
• Contract Administration and Oversight Guidelines for Intelligent Transportation Systems (ITS) Projects
  *Acceptance Test Plans (ATP). *Dynamic message sign factory acceptance test plan.
  17 KB (2,411 words) - 15:12, 19 June 2017
• Materials Quality Assurance Procedures Manual
  ...certification, retention of sampling and testing records, verification of test procedures, calibration of testing apparatus and participation in the devel ...tructure Expansion Anchors || Gen Cert || Revised basis of acceptance from Test to Gen Cert, removed sampling criteria per the Structural Fabrication Unit.
  34 KB (4,629 words) - 07:36, 3 August 2020
• 604 - Contractor Quality Control for Concrete
  ...tor with guidance so that the appropriate measures are taken to sample and test the concrete, administer the actions necessary to ensure that only concrete MDOT will not sample, nor test for quality control or assist in controlling the Contractor’s production
  30 KB (4,184 words) - 09:14, 14 February 2017
• 705 - Foundation Piling
  ...used piles must be in good condition, and the Contractor must provide mill test reports, and required Buy America certification. Contact the Geotechnical ...he contractor is using appropriate equipment to drive production piles and test piles without damaging them. The following pile driving equipment is subje
  29 KB (4,628 words) - 12:05, 28 August 2018
• ...se items should be clearly labeled as final measured), associated pay item test material usage and comments, comments on maintaining traffic and maintenanc
  3 KB (456 words) - 14:09, 28 January 2013
• 601 - PCC Pavement Mixtures
  ...beams, when made, should be reported on Concrete Cylinder/Core Compression Test Results, Form 1160B ([http://hct591jbosds790/wiki/index.php/File:602.02-2.j ...est first load (subsequent loads, if required). During concrete placement, test for slump at least once per hour.
  20 KB (2,966 words) - 09:05, 14 February 2017
• 101.04 - Inspector's Daily Reports
  ...se items should be clearly labeled as final measured), associated pay item test material usage and comments, comments on maintaining traffic and maintenanc
  3 KB (472 words) - 16:08, 27 April 2020

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)